Unsoloclic de Libre-mesh en sants-montjuic

uci batch <<BATCH
set lime.network=lime
set lime.network.primary_interface=eth0
set lime.network.main_ipv4_address='10.1.104.\M6\/22'
set lime.network.main_ipv6_address='2a00:1508:a01:6800::\M5\\\M6\/64'
set lime.network.bmx6_over_batman=false

set lime.wifi=lime
set lime.wifi.ap_ssid=jardi-botanic-lliure.guifi.net

add_list lime.network.resolvers=10.139.6.178

delete lime.eth5
delete lime.radio1
delete lime.radio12

commit

BATCH


cd /sys/devices/
for physPath in platform/ehci-platform/usb*/*/*/ieee80211/*
do
	phyName="$(basename ${physPath})"
	
	echo ${phyName} | grep -q 'phy[0-9]*' &&
	{
		phyIndex="$(echo ${phyName} | grep -o '[0-9]*')"
		uci batch <<BATCH
delete lime.radio${phyIndex}
delete wireless.radio${phyIndex}

set lime.radio${phyIndex}=wifi
add_list lime.radio${phyIndex}.modes=adhoc
set lime.radio${phyIndex}.channel_2ghz=1
set lime.radio${phyIndex}.adhoc_mcast_rate=6000
set lime.radio${phyIndex}.adhoc_ssid="libre-mesh"
set lime.radio${phyIndex}.adhoc_bssid="ca:fe:00:c0:ff:ee"

set wireless.radio${phyIndex}=wifi-device
set wireless.radio${phyIndex}.type=mac80211
set wireless.radio${phyIndex}.hwmode=11ng
set wireless.radio${phyIndex}.path="$(echo ${physPath} | awk -F"ieee80211" '{print $1}')"
add_list wireless.radio${phyIndex}.ht_capab="LDPC"
add_list wireless.radio${phyIndex}.ht_capab="SHORT-GI-20"
add_list wireless.radio${phyIndex}.ht_capab="SHORT-GI-40"
add_list wireless.radio${phyIndex}.ht_capab="TX-STBC"
add_list wireless.radio${phyIndex}.ht_capab="RX-STBC1"
add_list wireless.radio${phyIndex}.ht_capab="DSSS_CCK-40"
set wireless.radio${phyIndex}.htmode=HT20
set wireless.radio${phyIndex}.disabled=0

commit

BATCH
	}

done

lime-config

uci batch <<BATCH2

del_list network.lan.ifname=eth1

delete network.wan
delete network.wan6

commit

BATCH2

Si tu nodo es un gateway executa esto despues cambiando oportunamente las variables

wanIF="eth1" # rocket eth0, routerstation eth0
wanIP="10.139.6.190" # rocket 190, routerstation 185

uci batch <<BATCH

set network.wan=interface
set network.wan.proto=static
set network.wan.mtu=1500
set network.wan.ifname=${wanIF}
set network.wan.ipaddr=${wanIP}
set network.wan.netmask=255.255.255.240
set network.wan.gateway=10.139.6.178

del_list network.lan.ifname=${wanIF}

set bmx6.togw4=tunIn
set bmx6.togw4.tunIn=togw4
set bmx6.togw4.network=10.139.6.176/28

set bmx6.def4=tunIn
set bmx6.def4.tunIn=def4
set bmx6.def4.network=0.0.0.0/0

commit

BATCH

al siguiente reboot tu nodo estara' funcionando perfectamente